![okidata c5800 is drum part of toner cartridge okidata c5800 is drum part of toner cartridge](https://www.precisionroller.com/img/G2416.jpg)
Image Drum Unit, "C-Toner" for cyan toner, etc.), press the Enter buttonĪnd the last digit of the count will start flashing.Ģ) Press the Cancel button to decrease the digit amount or press the Press either the + or – button until "CONSUMABLE COUNTER SET" isĭisplayed, press the Enter button you are now in the menu to setġ) Press either the + or – buttons to scroll through the variousĬonsumables, at the desired consumable (ie. The display shows "Diag Mode xx.xx.xx S-Mode". We don\t want to do the NVRAM complete reset because we can lose network settings.ģ) The LCD Shows "OKI User", Scroll to "Engine Diag Mode", press "enter". Turn off toner page counting on the OKI C3200N The above change can also be made to the "Belt Unit" and i'm guessing Fuser unit aswell. The image drums, to stop any counting of the drum units, allowing them You can also apply the above change to the "ID Unit"s aswell, being
![okidata c5800 is drum part of toner cartridge okidata c5800 is drum part of toner cartridge](https://www.printerland.co.uk/images/Product_Images/c5800drumpack.jpg)
The * will appear, showing that you've set the value correctly. The value to "Disable" press both the 3 & 7 buttons together, and Scroll to "Toner Sensor".Ĭhange the values by using the 3 & 7 buttons. Use the 2 & 6 buttons to scroll between options. Use if you've turned off toner counting in the below step.Īfter getting into Eng Diag level 4, scroll down to "Engine Parameter Set 2". The (cnyk) toner percentages can be changed here manually, but is no The (cmyk) "ID Unit" shows how many pages have been printed that include that colour since that item has been installed.
![okidata c5800 is drum part of toner cartridge okidata c5800 is drum part of toner cartridge](https://s.yimg.com/aah/yhst-32530124372915/4-x-drum-unit-chip-for-konica-minolta-bizhub-c3351-c3851-fs-iup-24-17.gif)
There are also life limits for toners, drums, fuser units, belts etc, which can be changed from the default values. its there to make you replace the printer after x(600000) number of prints? The Printer life limit seems like an odd one. The "Replace" values for belt, fuser, drums, and toners show how many times each of those units have been replaced. The "Total Dot Count" is the same as the above, but for the entire life of the printer. The "Dot Count"s set how many times each colour has been used, in the life of that toner(?). The Toner counts are in percentages, and can be changed from 000% to 999%, where 0% is no use, and 100% is totally used. The screen will flash 3 times, then an * will appear at the endĨ) The "ID" unit appears to be the drums, setting these values changes the drum usage according to the printer. Use Buttons 2 & 6 to change that value.ħ) When you have made any changes you need to, hold down buttons 1, 3,Īnd 5.
![okidata c5800 is drum part of toner cartridge okidata c5800 is drum part of toner cartridge](https://www.precisionroller.com/img/G9954-3.wh.jpg)
Use buttons 3 & 7 to change the value you wish to alter.Ħ) The Flashing number is the value you have highlighted. Scroll down to "Counter Set".ĥ) Use Buttons 2 & 6 to scroll between menu items. The display shows "Diag Mode 01.02.02 S-Mode"ĥ) Scroll to Toner Sensor(it may be the first one), hit enter, Change setting to "Disable"Ħ) To set the "Disable" setting you need to press the ONLINE, CANCEL and - Buttons at the same time, pressing ONLINE first.Ĩ) Turn off the Printer, Leave for 10 seconds, and Turn back on, as normal.Ĭ7200 maintenance Menu's and reset tonner for C7200, C7300, C7500ġ) Turn on Printer while holding the 1 & 2 buttons.Ģ) Using button #1 scroll down untill you see "Diagnostic Mode xx.xx.xx", then hold down buttons 2 & 3.ģ) You now have "Engine Diag Mode Level 4" showing on the display.Ĥ) Use Buttons 1 & 5 to scroll between menu's.
OKIDATA C5800 IS DRUM PART OF TONER CARTRIDGE HOW TO
How to turn off toner page counting on the OKI C5400nĢ) Turn on printer, while holding the + and - buttons.ģ) The LCD Shows 'OKI User', Scroll to "Engine Diag Mode", hit enter.